Ublox NEO-M8N GPS Module with Compass for APM Pixhawk

(1 customer review)

400 7,200 


Ublox NEO-M8N GPS Module with Compass for APM Pixhawk Compass Support DJI Naza M V1 & V2 Lite Flight Controller.  A new generation Ublox GPS NEO-M8N, with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy, support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode or more.

Using 32-bit processor, compatible with NAZA M V1 & V2 flight controller, incomparably superior to 8-bit processor. Please take notice of the arrow on GPS, which stands for the head of a flyer. Similar calibration and usage with GPS Ublox NEO-M8N . Coming with soft silicone gel cable 30cm. For softness, black rubber was wrapped on a surface.

(Notice: black cable= GND, white cable=TX, yellow cable=RX, red cable=5V, 3.3-7.5V is ok), Metal foil label has been mounted on the bottom of GPS Ublox NEO-M8N to reduce signal interference from other electronic types of equipment

 Note: To calibrate the electronic compass is the first important thing when received your GPS.

 Calibration Method of Gps NEO-M8N :

Connect GPS to Flight controller, dial the model switch of radio control 7-10 times, LED light turns orange; Turn the flyer horizontally one circle, then the LED light turns green; Make the head of a flyer downwards and turn it one circle, then the LED light flashed on.
GPS Chip parameters:
  • Receiver type 72-channel u-blox M8 engine
    GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
    Galileo-ready E1B/C (NEO-M8N)
    Nav. update rate1 Single GNSS: up to 18 HZ
    Concurrent GNSS: up to 10 Hz
    Position accuracy2 2.0 m CEP
    Acquisition2 Cold starts: 26 s
    Aided starts: 2 s
    Reacquisition: 1.5 s
    Sensitivity2 Tracking & Nav: –167 dBm
    Cold starts: –148 dBm
    Hot starts: –156 dBm
    Assistance AssistNow GNSS Online
    AssistNow GNSS Offline (up to 35 days)
    AssistNow Autonomous (up to 6 days)
    OMA SUPL & 3GPP compliant
    Oscillator TCXO (NEO-M8N/Q),
    Crystal (NEO-M8M)
    RTC crystal Built-In
    Noise figure On-chip LNA (NEO-M8M). Extra LNA for lowest noise figure (NEO-M8N/Q)
    Anti jamming Active CW detection and removal. Extra
    onboard SAW band pass filter (NEO-M8N/Q)
    Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
    Supported antennas Active and passive
    Odometer Travelled distance
    Data-logger For position, velocity, and time (NEO-M8N)
  • Operating temp. –40° C to 85° C
    Storage temp. –40° C to 85° C (NEO-M8N/Q)
    –40° C to 105° C (NEO-M8M)
    RoHS compliant (lead-free)
    Qualification according to ISO 16750
    Manufactured and fully tested in ISO/TS 16949 certified production sites
    Uses u-blox M8 chips qualified according to AEC-Q100
  • Supply voltage 1.65 V to 3.6 V (NEO-M8M)
    2.7 V to 3.6 V (NEO-M8N/Q)
    Power consumption4 23 mA @ 3.0 V (continuous)
    5 mA @ 3.0 V Power Save Mode (1 Hz, GPS mode only)
    Backup Supply 1.4 to 3.6 V
  • NEO-M8N-0 u-blox M8 Concurrent GNSS LCC Module,
    TCXO, flash, SAW, LNA,
    Timepulse Configurable 0.25 Hz to 10 MHz

Main Features Gps NEO-M8N :

  • Ublox NEO-M8N GPS + Big Dipper + SBAS or GPS + GLONASS + SBAS
  • Built-in L883 electric compass, refresh rate increased to 10hz
  • Can receive more satellites signal, support for Galileo of Europe, GLONASS of Russia,
  • Lesser fluctuation and greater stability of Ublox NEO-M8N GPS
  • Superior anti-jamming performance
  • Brand name: NEO M8N
  • Item name: Ublox NEO-M8N GPS
  • Built-in: Electronic compass
  • Suit for: APM Pixhawk

Package Included:

  • 1 x Ublox NEO-M8N GPS Module with Compass
  • 2 x Double Tape
  • 1 x Stand kit

Other Products:

ESC Servo Extension Cable

IMAX B6AC 80W 6A Updated Balance Charger Discharge for Lipo/Li-ion/LiFe/NiMh Battery

How to Use:

Apm 2.8 Calibrate With GPS Neo M8N


Additional information



1 review for Ublox NEO-M8N GPS Module with Compass for APM Pixhawk

  1. Osaid (verified owner)

    Works fine but is a chinese clone without flash and firmware 2.01. Without flash upgrade tp 3.01 is not possible and parameters reset after each reboot.

Add a review

Your email address will not be published. Required fields are marked *